Happy with the bed after eliminating odor. See review and update.
Worth any penny This daybed, made in Vietnam, was exactly what I was looking for when I purchased it a year ago today (!) for a sewing/napping room. It came out of the boxes with two problems, one fixable, one chronic:
1) Fixable: One corner of the front trundle piece was cracked and split, obviously from box dropped in transit. The manufacturer wouldnt ship just the broken part, but referred me to . As always, service was good--offered to replace the entire bed if I returned all three boxes. The broken part was--of course--in the third box I unpacked. The packing was brilliantly done...styrofoam and parts fit like a monster puzzle. After laying out parts from the first two boxes, I couldnt hope to repack them for return. I gladly accepted a discount offer from and repaired the damage myself with marine epoxy, clamps, sander, and spray paint.
2) Chronic: The bed has a strong musty odor which I expected would eventually dissipate, but after a year is as bad as ever. The bed frame is labeled California 93120 Compliant for Formaldehyde Phase 2. Perhaps the bed frame is, but I wonder if that standard applies to the plywood slats. Ive tolerated the unpleasant odor because the room isnt often used, but after sleeping on the bed the last three nights, either the smell or the bed has to go. Today I took the bed apart. Except for the inside of the front and rear rails that support the slats, the bed frame pieces (wood, not particle board) have a smooth finish coat, in my opinion unlikely to be the odor source. The slats, however, are lightly sprayed and not well sealed with paint. I removed all the slats and stacked them in a warm place to test for odor. The bed and trundle frames stayed in the room awaiting the sniff test. Ill definitely replace the plywood slats with real wood (incense cedar if I could afford it) or worst case, repaint the entire bed. Buy American.
Update: August 19, 2017
Decided to work on existing slats rather than buying new. First I wiped down the entire bed with 50% vinegar/water. With a narrow roller, I applied water base Kilz primer to inside surfaces of front and back rails of bed and trundle that werent well-finished. Then on to the main objective, which was to prime and paint all edges and both sides of slats. A PVC frame from the garden was helpful to lay the slats on for drying. I did not remove the woven tape that holds the slats together. After the primer dried, I rolled water base Kilz paint on all slat surfaces and let them dry for three days. The mildew-y odor is gone, replaced by very faint scent of fresh paint which will probably fade with time. Happy to say I like the bed again.
Happy with the bed after eliminating odor. See review and update.
Worth any penny This daybed, made in Vietnam, was exactly what I was looking for when I purchased it a year ago today (!) for a sewing/napping room. It came out of the boxes with two problems, one fixable, one chronic: 1) Fixable: One corner of the front trundle piece was cracked and split, obviously from box dropped in transit. The manufacturer wouldnt ship just the broken part, but referred me to . As always, service was good--offered to replace the entire bed if I returned all three boxes. The broken part was--of course--in the third box I unpacked. The packing was brilliantly done...styrofoam and parts fit like a monster puzzle. After laying out parts from the first two boxes, I couldnt hope to repack them for return. I gladly accepted a discount offer from and repaired the damage myself with marine epoxy, clamps, sander, and spray paint. 2) Chronic: The bed has a strong musty odor which I expected would eventually dissipate, but after a year is as bad as ever. The bed frame is labeled California 93120 Compliant for Formaldehyde Phase 2. Perhaps the bed frame is, but I wonder if that standard applies to the plywood slats. Ive tolerated the unpleasant odor because the room isnt often used, but after sleeping on the bed the last three nights, either the smell or the bed has to go. Today I took the bed apart. Except for the inside of the front and rear rails that support the slats, the bed frame pieces (wood, not particle board) have a smooth finish coat, in my opinion unlikely to be the odor source. The slats, however, are lightly sprayed and not well sealed with paint. I removed all the slats and stacked them in a warm place to test for odor. The bed and trundle frames stayed in the room awaiting the sniff test. Ill definitely replace the plywood slats with real wood (incense cedar if I could afford it) or worst case, repaint the entire bed. Buy American. Update: August 19, 2017 Decided to work on existing slats rather than buying new. First I wiped down the entire bed with 50% vinegar/water. With a narrow roller, I applied water base Kilz primer to inside surfaces of front and back rails of bed and trundle that werent well-finished. Then on to the main objective, which was to prime and paint all edges and both sides of slats. A PVC frame from the garden was helpful to lay the slats on for drying. I did not remove the woven tape that holds the slats together. After the primer dried, I rolled water base Kilz paint on all slat surfaces and let them dry for three days. The mildew-y odor is gone, replaced by very faint scent of fresh paint which will probably fade with time. Happy to say I like the bed again.